Part No. | Features | VCC(V) | Package |
93334 | High Energy Ignition Circuit
* Very Low Peripheral Component Count
* No Critical System Resistors
* Wide Supply Voltage Operating Range (4.0V ~ 24V)
* Overvoltage Shutdown (30V)
* Dwell Automatically Adjusts to Produce Optimum Stored Energy without Waste
* Externally Adjustable Peak Current
* Transient Protected Inputs and Outputs | 4.0~24.0 | SOP-8 |
M4213 | Ignition Controller of Motorcycle
* Power supply by magnetoelectric motor and clamping at 9.2V
* Less external components and wide applicability
* Low static current, typical is 5mA
* High quality and stability for using 5μm Bipolar process | 9.0~9.5 | DIP-14
SOP-14 |
UL497 | Hall Effect Pickup Ignition Controller
* Direct driving of the external power darlington
* Coil current charent charging angle control
* Programme coil current peak limitation
* When 94% nominal current not reached programmable dwell recovery time
* RPM output
* Has peranent conduction protection
* Overvoltage protection
* Internal supply zener
* Reverse battery protection | 3.5 | SOP-16 |
UU6043B | Single Output Flasher IC for 18mohm shunt
Temperature and supply voltage compensated frequency
* Warning indication of lamp failure by means of frequency doubling
* Relay driver output with high current carrying capacity and low saturation output
* Minimum lamp load for flasher operation: ≥ 1 W
* Very low susceptibility to EMI | 9.0~15.0 | SOP-8
DIP-8 |
UU4761 | FLASHER IC
* The static operating current<5mA
* Wide operating voltage range
* Very low susceptibility to EMI | 9.5~18.0 | SOP-8
DIP-8 |
U2043 | Flasher, Shunt, Pilot Lamp to GND or Vbatt
*Temperature and voltage compensated frequency
*Warning indication of lamp failure by means of frequency doubling
* Minimum lamp load for flasher operation ≥10 W
*Relay output with high current carrying capacity and low saturation voltage
*Low susceptibility to EMI | 9.0~15.0 | SOP-8
DIP-8 |
L2044 | Dual Output Flasher
* Temperature and Supply Voltage Compensated Flashing Frequency
* Frequency Doubling Indicates Lamp Fault.
* Two Relay Driver Outputs with High Current-carrying Capacity and Low Saturation Voltage
* Minimum Lamp Load for Flasher Operation: ≥ 1W
* Very Low Sensitivity to EMI
* Extremely Low Current Consumption<10μA ( at Switches Open)
* Reverse Polarity Protection
* Three Control Inputs: Left, Right and Hazard Warning | 8.0~18.0 | SOP-14
DIP-14 |
LL204 | DUAL OUTPUT FLASHER
* Temperature and supply voltage compensated flashing frequency
* Frequency doubling indicates lamp fault.
* Two relay driver outputs with high current-carrying capacity and low saturation voltage
* Minimum lamp load for flasher operation: ≥ 1W
* Very low sensitivity to EMI
* Extremely low current consumption<10μA ( at switches open)
* Reverse polarity protection
* Three control inputs: left, right and hazard warning | 8.0~18.0 | SOP-14
DIP-14 |
UU6032B | Automotive toggle switch IC
* Relay driver with Z-diode
* RC oscillator determines switching characteristics
* Debounced input for toggle switch
* Three debounced inputs: ON, OFF and TOGGLE
* RF interference protection
* Load-dump protection | 6.0~16.0 | SOP-8
DIP-8 |
UU6046B | Rear window heating timer
* Delay time range: 3.7s to 20h
* Relay driver with Z-diode
* RC oscillator determines switching characteristics
* Debounced input for toggle switch
* Two debounced inputs: ON and OFF
* Load-dump protection
* RF interference protected
* Inputs switched to VBatt | 6.0~16.0 | SOP-8
DIP-8 |
UU6047B | Rear window heating timer
* Delay time range: 3.7s to 20h
* Relay driver with Z-diode
* RC oscillator determines switching characteristics
* Debounced input for toggle switch
* Two debounced inputs: ON and OFF
* Load-dump protection
* RF interference protected
* Inputs switched to ground | 6.0~16.0 | SOP-8
DIP-8 |
UU642 | Interval and wipe/wash wiper control IC
* After-wiping time: 2s~20s
* Interval pause: 4s~20s
* Wipe/wash mode priority
* Wiper motor’s park switch
* Relay driver with Z-diode
* One external capacitor determines all time sequences
* Interference protection according to VDE 0839 or ISO/TR 637/1
* Load-dump protected | 9.0~16.5 | SOP-8
DIP-8 |
UAC33092 | Alternator Voltage Regulator
*Forced Load Response Control (LRC) with Heavy Load Transitions at Low RPM
*Capable of Regulating Voltage to ±0.1 V @ 25℃
*Operating Frequency Selectable with One External Resistor
*< 0.1 V Variation over Speed Range of 2000 to 10,000 RPM
*< 0.4 V Variation over 10% to 95% of Maximum Alternator Output
*Maintains Regulation with External Loads as Low as 1.0 A
*Load Dump Protection of Lamp, Field Control Devices, and Loads
*Duty Cycle Limit Protection
*Provides High Side MOSFET Control of a Ground Referenced Field Winding
*Controlled MOSFET and Flyback Diode Recovery Characteristics for Minimum RFI
*Optional 2.5 or 10 sec. LRC Rate Control (Osc. Freq. = 280 kHz)
*Undervoltage, Overvoltage and Phase Fault (Broken Belt) Detection | 11.5~16.5 | SOP-20
SOP-24 |
UAC33092A | Alternator Voltage Regulator
* Forced load response control (LRC) with heavy load transitions at low RPM
* Voltage regulated to ± 0.1V @ 25°C
* External resistor adjustable operating frequency
* Regulation is effective with loads as high as 1.0A
* Load dump protection of lamp, field control devices, and loads
* Undervoltage, overvoltage , phase fault (broken belt) detection and duty cycle limited protections | 11.5~16.5 | SOP-20 |
UU4793 | Overload Monitoring with Resistive Load, VT = 44.5 mV
* Two common reference comparators
* Tight threshold tolerance
* Constant threshold
* Output with NPN
* 8 kV - ESD protection
* Protection of reverse polarity
* Load-dump protection | 9.0~15.0 | SOP-8 |
UL497 | Hall Effect Pickup Ignition Controller
* Direct driving of the external power Darlington * Coil current charent charging angle control
* Programme coil current peak limitation * When 94% nominal current not reached programmable dwell recovery time
* RPM output * Has peranent conduction protection * Overvoltage protection
* Internal supply zener * Reverse battery protection | 3.5 | SOP-16 |
在线咨询
微信服务
